TV
Repair Database
|
Goldstar |
20A80 |
No picture. |
FR406 OC ( NO
FIELD ) |
|
Goldstar |
20A80AF |
Int reverts to st/by &
won't come back on |
Sw mode tfmrT801
int o/c HT winding pt no 151-148A |
|
Goldstar |
2168F |
FIELD CRAMP ,
LINE ACROSS SCREEN |
C309 ( TANT
) 0.22mfd |
|
Goldstar |
C1I20C22F CI21C22F |
No response to R/C or front
controls |
Replace C814 & Q811 |
| Goldstar |
CB14A80E |
Reduced width. 6-8 volts on supply pin of TDA8362 |
Replace TDA8362. Supplying +12V to supply pin of TDA8362,
restored width but with no hor. Synchronization. |
| Goldstar |
CB14A80E |
Reduced width. 6-8 volts on supply pin of TDA8362 |
Replace TDA8362. Supplying +12V to supply pin of TDA8362,
restored width but with no hor. Synchronization. |
| Goldstar |
CB14A80E |
Relay goes on, then off, immediately after switch on |
Change memory chip St24C02C. |
| Goldstar |
CB14A80E |
Relay goes on, then off, immediately after switch on |
Change memory chip St24C02C. |
| Goldstar |
CBZ9222E |
No horizontal sync. when cold. When hot, everything is OK.
It was not possible to track the defective component with a freezer spray. |
Changed several caps around TDA2579 chip. |
| Goldstar |
CBZ9222E |
No horizontal sync. when cold. When hot, everything is OK.
It was not possible to track the defective component with a freezer spray. |
Changed several caps around TDA2579 chip. |
|
Goldstar |
CF25C22F |
Width excessive with bowing |
C413 10µ 250v u/s caused
by C405 0µ22 low cap |
|
Goldstar |
CF25C22F CF28C22 |
DEAD SET
, RELAY CHATTERS
, D401 SC |
CHANGE , R308 - 33R
3W ORSO322L667 ,
D401 , D402 - RU4DS ODD400000AB
, X501 - 156-A05B .
ALSO CHECK IC301 ,
ZD304 . |
|
Goldstar |
CF25C22F CF28C22F |
Dead - no line drive - 150v
HT ok |
SCL & SDA missing at
pins 4 & 5 IC503. Replace X01N on Nicam pcb or IC03N if that doesn't
cure it |
|
Goldstar |
CF25C22F CF28C22F |
Dead Q801 chopper tr s/c |
Reduce R810 from 12k to 6k8 |
|
Goldstar |
CF25C22F CF28C22F |
Dead with relay chattering |
Change R308 to 33R 3w,
D401/402 to RU4DS & X501 to pt no 156-A05B |
|
Goldstar |
CF25C28CF |
Field collapse |
Fit kit which contains
TDA8350QN5 (don't use TDA8350Q) |
|
Goldstar |
CF25C28F |
E-W Dist |
Q351 KTB988Y s/c e-c &
FR359 22R ½w fus res high |
|
Goldstar |
CF25C28F |
Field collapse |
IC351 TDA8350Q & mod
kit KITPC58A |
|
Goldstar |
CF28A50
PC58A |
Field - dist top edge of
pic |
Check electrolytics in
field stage & fop chip IC351 TDA8350Q |
|
Goldstar |
CF28C22F |
Dead - all psu volts
present - lop tr hot |
C405 0µ22 400v bulged
& leaky (checked ok out of cct) |
|
Goldstar |
CF28C28F |
Field collapse |
Replace IC351 TDA8350CQ fop
chip & check adequate heatsink compound & clip is secure |
|
Goldstar |
CF29C20N |
E/W & field adj
problems after changing TDA8350Q |
Add 220R res across b-e of
Q301 |
|
Goldstar |
CI14A20 |
No tuning - osd works |
No 33v tuning supply -
FR403 5R6 o/c |
|
Goldstar |
CI14A80 |
Reverts to st/by aft few
secs |
EEPROM 24C04 - does not req
preprog chip |
|
Goldstar |
CI14A80 CI14A80F |
ORIGINAL TUBE NO LOGER
AVAILIABE , ORDER Pt No 205 |
C422-0.39uF 20v 181-013C
, L402 H.LIN 150-LO2B
, R424 6k8 2W
ORS6801K607 ,
FR404 10R 1W ORF0102J607 ,
C902 270pF OCN2710K519 |
|
Goldstar |
CI14A80F |
Dead - chopper Tr BUZ90A
s/c |
R821 150k o/c also replaced
R802 680k; R819 130k; R806 120k - TDA4605-2 may have been damaged but
wasn't |
|
Goldstar |
CI14A80F CI20A80F CI21A80F |
Dead - Q801 chopper tr s/c |
Replace IC801 & check
R821 150k & R806 120k |
|
Goldstar |
CI14A80F CI20A80F CI21A80F |
Dead - R802 680k failed |
Fit 1w version instead of
½w |
|
Goldstar |
CI14A80F CI20A80F CI21A80F |
No tuning or tuner drift |
Check Q18 - if no 33v check
FR403 - if o/c fit 1R ½w |
|
Goldstar |
CI14E20F CI20E20 |
SOUND OR COLOUR VARIES INT. |
IC01 Pt No OISG853403A .
CHECK ALSO Q06 FOR DRY JOINTS . |
|
Goldstar |
CI14E20F CI20E20F CI20A96F |
Int sound & col
variation |
Replace IC01 & check
Q06 for dry joints |
|
Goldstar |
CI20A50 |
Field collapse |
FR718 3R3 o/c |
|
Goldstar |
CI20A80 |
No pic |
Check FR406 26v fuse in fop
stage |
|
Goldstar |
CI21A80 etc |
Won't come on from st/by |
May be in child lock - use
r/c to sw on |
|
Goldstar |
CI21C22F |
dead |
dry joints in lop stage |
|
Goldstar |
CI21C22F |
height varies with audio
content |
HT smoothing cap 220µ 160v |
|
Goldstar |
CI21C22F |
Running PSU on dummy load |
ground base of Q812 |
|
Goldstar |
CI21C22F |
Trips at sw on |
Lop tr leaky (reads ok out
of cct) |
|
Goldstar |
CI-21C22T |
int start up, int no pic,
int txt |
dry joints |
|
Goldstar |
CI4A80A |
Dead - 4A fuse blackened |
R821 150k hi res, BUZ90
Q801 chopper s/c & replace TDA4605-2 chopper chip |
|
Goldstar |
CI9902F |
St/by only |
R761 2k7 hi res |
|
Goldstar |
CI9902F |
Stuck in standby. |
R761 2k7 HIGH |
|
Goldstar |
CI990LT |
St/by only - relay clicks
at sw on |
HT low at 60v instead 115v
- check C8075 33µ 160v |
|
Goldstar |
CIS4361 |
No picture - sound ok |
no crt htrs due to
taernished pins on 4 pin connector by Loptx |
|
Goldstar |
CIS4361 |
No picture. |
4 Pin connector by LOPT
pins tarnished ( feed to heaters ) |
|
Goldstar |
CIS4441 |
Bright white raster - sound
ok |
Replaced R424/425 Ibeam res
under loptx - - A1 setting VERY critical |
|
Goldstar |
CIS4441 |
Brightness excessive with
pic appearing only briefly at sw on |
Check/replace resistors
680k on crt base |
|
Goldstar |
CIT 2172X |
int start up, int no pic,
int txt |
C811 47µ 25v, C812 100µ
16v,C808 1µ 50v, C813 100µ 16v remove glue, check relay |
|
Goldstar |
CIT 2190F |
No sound. |
CHECK FOR MUTE STATE IC1401 |
|
Goldstar |
CIT2068F |
St/by only - if mains sw
held in snowy raster shows |
Micro IC701 pins 31 &
32 had no 10Mhz signal present - Xtal faulty |
|
Goldstar |
CIT2068F |
Stuck in StBy - if switch
held in set starts but o |
No 10Mhz on pins 31 32 of
micro as xtal us |
|
Goldstar |
CIT2162X |
Int loss of signals |
Tuning vots increases to
31v - bad conn on lead between tuner prescaler & tuning pcb |
|
Goldstar |
CIT2162X |
INT low gain or just snow
tuning VOLTAGE AT 30v |
INT OC IN LEAD FROM
PRESCALER TO TUNING PCB |
|
Goldstar |
CIT2162X |
Low brightness. |
C820 ( 10uF
) |
|
Goldstar |
CIT2162X PC08X8 |
Dark - only get pic when A1
at max |
180v to vid stage high at
278v; C401 10µ 160v on 112v rail o/c |
|
Goldstar |
CIT2168 |
Dead - 118v HT low at 50v |
C806S 47µ 160v HT
smoothing cap |
|
Goldstar |
CIT2168 |
Field collapse - int |
Pin 5 TDA1170N was 5v
instead of 25v. D301 1N4003 faulty. If chip turns out to be faulty use
genuine Goldstar chip (others won't work - allegedly) Also check R320 10R
1w |
|
Goldstar |
CIT2168 |
Int start up |
D401
1N4003 o/c in line dr supply |
|
Goldstar |
CIT2168 |
No start up |
Check R811P 22k 3w, D805P
R10J in start up cct, C805P 100µ 16v |
|
Goldstar |
CIT2168 |
Sound muted & goes to
Stby after 10mins. |
Replace the TDA1940 IC401
remove the link J8 & fit 1k instead. |
|
Goldstar |
CIT2168 |
Txt absent |
Dry joints conn P102 on txt
pcb |
|
Goldstar |
CIT2168F |
Field foldover |
C423, C302 100µ 35v |
|
Goldstar |
CIT2168F CIT2190F etc |
No sound - pic ok - sw to
st/by aft 10 mins |
Pin 7 IC401 TDA1940
produces muting o/p - chip u/s. Fit 1k res in place of J8 link |
|
Goldstar |
CIT2170 |
Fails to power up from StBy |
D/J on main relay : remove
retin & replace |
|
Goldstar |
CIT2170F |
No start up or int sw off |
Check for dry joints on
main relay |
|
Goldstar |
CIT2170F |
Patterning from cold |
C827 1000µ 25v leaky |
| Goldstar |
CIT2170F |
Patterning horiz lines on pic |
C827 1000µ 25v - tested ok on esr meter |
|
Goldstar |
CIT2172 |
Cannot store contrast
setting (Too low) |
Normal - change R520 to 18k |
|
Goldstar |
CIT2172X |
No Text after replacing
TDA3651. |
Must only use TDA as
supplied By Goldstar |
|
Goldstar |
CIT2172X |
Remains in search mode |
R80 1M5 high res |
|
Goldstar |
CIT2172X CIT2175X |
Low contrast at sw on &
can't be stored |
Replace R520 with 18k |
|
Goldstar |
CIT2172X CIT2175X |
No sound when playing pre
recs |
Adj L204 quarter turn
clockwise |
|
Goldstar |
CIT2175X |
Frame - height &
linearity poor. |
C202 ( 0.22uf ) connected
to pin 2 of TDA4502. |
|
Goldstar |
CIT2175X |
Int dead with motorboating
sound |
Check all elects in psu -
remove glue first by freezing |
|
Goldstar |
CIT2175X |
Int loss of sound & pic |
L202 - green coil labelled
2K2 was int o/c |
|
Goldstar |
CIT2175X |
Linearity poor/lach of
height |
C202 0µ22 in field osc cct |
|
Goldstar |
CIT2175X |
Poor height / lin |
C202 0.22µ connected to
pin 2 TDA4502 |
|
Goldstar |
CIT2175X |
Slow start up |
C811 47µ 25v also check
C812 100µ 16v, C808 1µ 50v & C813 100µ 16v |
|
Goldstar |
CIT2176 |
Dead - fuse blown |
R806 270k o/c, IC801
TDA4601 s/c, Q802 2SD1911 s/c, R801 4R7 5w o/c |
|
Goldstar |
CIT2176 |
Trips then into st/by |
C710 4µ7 250v |
|
Goldstar |
CIT2180 |
Frame collapse. |
IC301 & R320 |
|
Goldstar |
CIT2180 |
Lack of width & height
with line across centre of screen |
C807 33µ 160v |
|
Goldstar |
CIT2180 |
No tuning. |
FR401 ( ON 40V RAIL
) |
|
Goldstar |
CIT2180 |
Sound muted & goes to
Stby after 10mins. |
Replace the TDA1940 IC401
remove the link J8 & fit 1k instead. |
|
Goldstar |
CIT2180F |
Dead |
hairline cracks around pins
of chopper tfmr |
|
Goldstar |
CIT2181 |
Int loss of Sync. |
C413 LEAKY |
|
Goldstar |
CIT2181 |
tripping - HT only 65v |
C807S leaky |
|
Goldstar |
CIT2181FG |
Colour disappears aft 20
mins |
Freezing chroma Del line
brought it back - DL faulty |
|
Goldstar |
CIT2181FG |
Dark
pic, lack of height & field non lin |
C806S 47µ 160v |
|
Goldstar |
CIT2181FG |
dead |
HT low at 25v (118v) on
dummy load; C807S 4µ7 160v |
|
Goldstar |
CIT2181FG |
Dead |
C801P 10µ 16v & C805P
100µ 16v hi esr, dry joints D803S |
|
Goldstar |
CIT2181FG |
Dead - no LED |
C805P 100µ 16v in psu |
|
Goldstar |
CIT2181FG |
Flyback lines at top of
screen when cold |
C302 100µ 35v |
|
Goldstar |
CIT2181FG |
Pic int blanked off - sound
ok |
Txt causing fault
- to disable txt pcb link pins 1 & 2 skt 1, 1 & 5 skt 2, 2
& 6 skt 2 & pin 10 skt 1 to pin 4 skt 2 |
|
Goldstar |
CIT2181FG |
Sync int lost |
I/p to TDA1940 chip lost
due to leaky C413 |
|
Goldstar |
CIT2181FG |
Txt lines showing |
C302 100µ |
|
Goldstar |
CIT2190 |
Field collapse preceded by
lines at top |
TDA1170N IC301 u/s caused
by C311 100µ 35v by chip |
|
Goldstar |
CIT2190 |
Txt int |
Dry joints Q1 emitter on
Txt pcb |
|
Goldstar |
CIT2190F |
Dead - No line drive |
D401 oc 1N4003 |
|
Goldstar |
CIT2190F |
Field collapse |
TDA1170N
IC301 u/s caused by C302 100µ 35v |
|
Goldstar |
CIT2190F |
No pic, line drive or EHT |
D401
1N4003 o/c in line dr supply |
|
Goldstar |
CIT2190F |
No sound |
CHECK FOR MUTE STATE IC1401 |
|
Goldstar |
CIT2190F |
No sound -
Disconnect P7 of IC401 if sound Ok. |
IC401 |
|
Goldstar |
CIT2191 Etc |
DEAD 330v SUPPLY OK |
C805 100uF 16v CHOPPER
COUPLER OC |
|
Goldstar |
CIT2570F |
Field cramped &
foldover with no lum for first 2 mins |
C308 2200µ in 16.5v rail
hi esr |
|
Goldstar |
CIT2588 |
Pic int blanks out (no lum) |
Replace VC53 on Txt pcb |
|
Goldstar |
CIT2588F |
PICTURE BLANKS OUT INT. |
VC53 Pt No 181-169A |
|
Goldstar |
CIT4175 |
St/by only - dead when sw
on |
No line drive - D812 1N4003
o/c |
|
Goldstar |
CIT4785 |
Dark pic with field non lin |
C820 HT cap 10µ 160v |
|
Goldstar |
CIT4785 |
Field collapse |
40v wform at pin 2 of
LA7830 chip - check C305 100µ 16v |
|
Goldstar |
CIT4785 |
Int no sound/pic/field
collapse - display stuck on "0"; no r/c or front controls |
int s/c on 12v line - P101
pin 11 s/c to adj pin |
|
Goldstar |
CIT610S |
St/by only with squeal |
C830 220µ 25v o/c, R808
270k replaced as a precaution, C818 1µ 50v o/c, C802 100µ 25v hi esr,
R811 1R ½w o/c |
|
Goldstar |
CIT9172 |
Dead - click from speaker
at switch off. |
FR817 ( 5.6R )
o/c. |
|
Goldstar |
CIT9172 |
Dead - fuse blown. |
Q801 ( 2SD1878 )
s/c , IC801 ( TDA4601 ) faulty
, R811 ( 120k ) o/c. |
|
Goldstar |
CIT9172 |
Frame collapse. |
IC401 ( TDA8214A ) |
|
Goldstar |
CIT9172 |
Height slowly decreases
from switch on. |
FR718 high at 26R |
|
Goldstar |
CIT9172 |
Int pic - sound ok |
Dry joints fop chip IC401 |
|
Goldstar |
CIT9172 |
No frame. |
IC401 ( TDA8214A ) |
|
Goldstar |
CIT9172 |
Will not tune in - snowy
raster. |
R821 ( 6.8k )
o/c. |
|
Goldstar |
CIT9325 |
No pic, sound & EHT OK
& Not field collapse |
If when connecting an RGB
o/p tr coll to chassis via
10k res the pic returns until sw off, change TDA3562A col dec chip |
|
Goldstar |
CIT9508 |
Dark
pic, lack of height & field non lin |
C820 10µ 160v |
|
Goldstar |
CIT9508 |
Dead, relay clicks at sw on
but no line drive |
FR802 1R fusible in 22v
supply o/c for no apparent reason |
|
Goldstar |
CIT9508 |
Int dark or no pic |
Int A1 control |
|
Goldstar |
CIT9508 |
No picture or int dark
picture |
A1 control on lopt int oc |
|
Goldstar |
CIT9508 |
Pic fades out due to loss
of crt heaters |
Dry joints P451 crt htr
supply on main pcb |
|
Goldstar |
CIT9902F |
Dead |
No 110v to lop stage -
D803S dry jointed in mains bridge rect cct |
|
Goldstar |
CIT9902F |
Not starting , HT low. |
C807S OC 33uF. |
|
Goldstar |
CIT9902F |
St/by only |
Osc feed to IC701 X701
10Mhz Xtal u/s |
|
Goldstar |
CIT9902F |
Won't come on unless sw to
st/by first |
Start up supply low due to
D401 hi res |
|
Goldstar |
KI14V38 |
No pic, no OSD, sound ok |
SDA bus is low because of
leaky zener ZD502 5.1V |
|
Goldstar |
KI14V38 KI20V38 |
UNSTABLE COLOUR ON PLAYBACK
. |
CHANGE C519 TO 15pF 50v
OCC1500K415 ,
IC502 TO TDA4665 OIPH466500B . |
|
Goldstar |
KY14V30 |
Dead - both TV & VCR
sects |
STR6707 power chip s/c;
ZD802 6.8v zener leaky |
|
Goldstar |
P58A |
Field lin - top 1/2 of pic
collapsed |
TDA8350Q field/EW chip
IC351 |
|
Goldstar |
P58A |
No E-W corr |
FR359 10R 1/2w fusible o/c |
|
Goldstar |
PC04A |
Black blobs on top sides of
screen |
C406 1µ 160v in line scan
coupling |
|
Goldstar |
PC04A |
Dead |
No HT - rect D803 o/c |
|
Goldstar |
PC04A |
Field lin dist top 1/4 of
pic |
D301 flyback boost cap
leaky - used 1N4001 |
|
Goldstar |
PC04A |
Field scan problems |
IC301 TDA1170N TFK version,
C301 1000µ 35v, C302 100µ 35v, C309 & C311 0µ22 35v & D301,
R320 is 10R 1w |
|
Goldstar |
PC04A |
Frame collapse. |
TDA1170A SC
REPLACE C311 ALSO |
|
Goldstar |
PC04A |
No sound & reverts to
st/by aft 10 mins |
Replace IC401 & fit 1k
res in place of link J8 |
|
Goldstar |
PC11A |
Int operation |
Dry joints TDA8214 IC401 or
chip faulty - screen cover must be fixed firmly for IF to work |
|
Goldstar |
PC31A |
dark lines, whine |
C812 0.22µ, 63v connected
to pin 7 of IC801 |
|
Goldstar |
PC31A |
Dead - psu running |
Line dr was 20khz, No 12v
to IC501 TDA8362 - Reg IC401 7812 o/c |
|
Goldstar |
PC31A |
Momentarily trips on bright
scenes |
R802 680k had wrong value
(68k) fitted |
|
Goldstar |
PC31A |
Poor HT reg & sw off on
prolonged bright pic |
R802 had incorrect value of
68k instead of 680k |
|
Goldstar |
PC-33 |
Vert dist with lines across
screen |
C305 6µ8 100v bi-polar |
|
Goldstar |
PC33J |
field collapse |
fit KITPC33J from CPC -
includes diodes chip etc |
|
Goldstar |
PC33J |
Field o/p chip repeatedly
fails |
Fit mod kit KITPC33J |
|
Goldstar |
PC33J |
Lack of height |
FR301 1R in fop hi res |
|
Goldstar |
PC42 |
Blank raster with on screen
display, no sound |
IC831
12v reg faulty - low o/p |
|
Goldstar |
PC42B |
No start up - led indicator
works |
HT low at 35v (109v); 12v
Reg IC831 |
|
Goldstar |
PC53A |
No front control op
"Lock on" displayed when attempting to turn off with hset |
EEPROM 24C08 |
|
Goldstar |
PC58A |
E/W distortion |
C359 & L351 running
hot. O/c print by Q351 |
|
Goldstar |
PC58A |
Field Collapse |
TDA8350Q field/EW chip
IC351 |
|
Goldstar |
PC73A |
Flyback lines at top of
screen when cold |
FR359 10R fusible o/c |
|
Goldstar |
RC7013 |
AGC action - pulls/poor pic
on weak sig |
C707 4µ7 50v |
|
Goldstar |
RC7031 |
Critical AGC level
adjustment cut off |
C707 4.7mfd 50v |
|
Goldstar |
KBV-9012E TV/VCR Combo |
White raster with retrace lines, the set switches off after
a while. L901 (in series with +180V supply to RGB trs) oc, the +180V
winding of Loptx delivers 300V!! (Di&smooth.Cap OK) |
Replace C820 10uF/160V cap. Note that +180V supply delivers
300V, while +B and all other voltages are normal. Seems to be a weird
LOPTx fault, but it was C820 instead. |
|
Goldstar |
KBV-9012E TV/VCR Combo |
White raster with retrace lines, the set switches off after
a while. L901 (in series with +180V supply to RGB trs) oc, the +180V
winding of Loptx delivers 300V!! (Di&smooth.Cap OK) |
Replace C820 10uF/160V cap. Note that +180V supply delivers
300V, while +B and all other voltages are normal. Seems to be a weird
LOPTx fault, but it was C820 instead. C820 IS NOT the smoothing cap for
+180V. |
