Goodmans

Goodmans

BRIDGEND & DISTRICT AMATEUR RADIO CLUB
GW4LNP/GC4LNP

TV Repair Database
Goodman's	1404	Tuning slightly off	Adjust T103 AFC tank coil
Goodmans	1410	Dead	start up res RP44 & series connected ones 68k could be o/c
Goodmans	1410	Dead - no st/by led	RP44 68k ¼w in psu o/c
Goodmans	1410	Line tearing /squeak	CP90 22µ 50v in psu
Goodmans	1430	St/by only	R302 o/c (dc feed to pin 21 IC301)
Goodmans	2032	Dead - smoking	C444 330pf 2kv
Goodmans	2043	Dead	psu working but no 106v o/p at D803 - FR803 4R7 fusible dry joints
Goodmans	2170	excess brill	No 190v on crt pcb. 100µH choke in series with supply o/c
Goodmans	2175	St/by only	R102, R103 150k o/c - also check R104, R105 270k
Goodmans	2180	Dead	R801 270k in psu o/c
Goodmans	2180	low brill esp at sw on	A1 volts low - conductive glue on crt base
Goodmans	2180	No pic - sound ok	No volts coll line dr tr due to o/c tfmr pri
Goodmans	2180	Partial Field collapse	Q212 2SC2073 o/c
Goodmans	2180	Top foldover	Dry joint D206 in fop cct
Goodmans	2195	: Excess Width (after transformer replacement)	Change value of C411 from 0.33 to 0.47
Goodmans	2575	dead	2A fuse o/c; chopper tr S2000AF s/c; replace C102 100µ, C103 100µ, C107 100µ; D33 1N4007 mains rect s/c;
Goodmans	2575	Dead - Ht very low	BY448 diode in EW stage s/c
Goodmans	2575	Dead with chirp	C134 10n, 1k6 burnt, loptr S2055AF s/c
Goodmans	2575	dead with smoke	dry joint/ burnt C134; D45 BY228
Goodmans	2575	Dead with smoke	Link 13 dry joints
Goodmans	2575	E/W faulty	TDA4950 - volts readings don't agree with cct diag even when ok
Goodmans	2575	No red	R26 68k on crt base o/c
Goodmans	2575	off burning smell	10R 5w resistor feed to lop tr overheats. Lop tr leaky, when replaced eht hi. C134 10n line flyback tuning cap had dropped in value
Goodmans	2575	reverts to st/by aft few secs	C108 in chopper cct
Goodmans	2576	E/W faulty	IC18 TDA4950
Goodmans	2580	Sound missing	TS90 BC848B sm in sound mute stage
Goodmans	2875	At sw on spkrs pop then shuts down	D35 (BA157) in PSU. It read OK in and out of circuit
Goodmans	2875	Dead	C102 100µ 25v in psu hi esr
Goodmans	2875	Dead	EW mod diode BY448 s/c & check for dry joints
Goodmans	2875	Dead	C134 E-W cap dry joints & S2055AF lop tr leaky
Goodmans	2875	dead	ew diodes D45/47 s/c & pincush chip IC18 - dry joints C134
Goodmans	2875	Dead - pri HT only	PTC2 small blue start up therm o/c
Goodmans	2875	Dead (possibly - no fault submitted with cure)	C143 0µ01 1600v
Goodmans	2875	Dead with burning smell	0µ01 1.6k cap in line stage burnt; BY228 leaky
Goodmans	2875	Dead with burning smell	0µ1 1.6kv cap burnt, BY228 adj to cap leaky
Goodmans	2875	E-W fault (aft burn up)	TDA4950 E-W chip
Goodmans	2875	Int dead	Dry joints chopper tfmr
Goodmans	2875	Int dead	Dry joints chopper tfmr pins
Goodmans	2875	No blue	R29 68k on crt base o/c
Goodmans	2875	No Blue	R29 68k on crt base o/c
Goodmans	2875	No E-W or width control	TDA4950
Goodmans	2875	Smeary, defocused or 1 pri col missing	Check 3 x 68k res on crt base
Goodmans	3375	Dead	dry joints chopper trfmr
Goodmans	5160	Excess brightness	C629 100µ 25v
Goodmans	110	DEAD , ONLY S.BY LIGHT	CHECK FOR 15v
Goodmans	110	DEAD , POWER SUPP UNDER LOAD	CHECK REGULATOR TRANS , AND AN5512 Pt No. 10 20 0103 2SA1012 - TRAN2SA1012
Goodmans	11AK19-8	Dead - no st/by	R806 22k
Goodmans	14"	BLANKED 3/4 PIC	R83 100ohm
Goodmans	1400	FIELD COLLAPSE	R306 10R o/c ALSO CHECK BLACK WIRE LINKING control PCB to centre of main PCB for D/J
Goodmans	1401	FIELD COLLAPSE	C308 ( tantalum ) SITUATED BY PIN 29 TA7698
GOODMANS	1403/2053	MAX VOLUME IS LIMITED	IN TEST MODE TO EXIT HOLD VOLUME DOWN BUTTON WHILE TURNING ON POWER
Goodmans	1403/2053	MAX VOLUME IS LIMITED	IN TEST MODE TO EXIT HOLD VOLUME DOWN BUTTON WHILE TURNING ON POWER
GOODMANS	1405R	DEAD,Q602 BLOWN APART	REPLACE R601 (4.7OHM), R612 (0.56OHM), Q602 (BC639), R607 (4R7) STR58041
Goodmans	1405R	DEAD,Q602 BLOWN APART	REPLACE R601 (4.7OHM), R612 (0.56OHM), Q602 (BC639), R607 (4R7) STR58041
Goodmans	1408	USUAL 27MEG TYPE FAULTS	27MEG CRYSTAL
Goodmans	141	WONT START ( WORKS FROM REMOTE )	220k FRONT PANEL
GOODMANS	1410	BLOWS 150V ZENER	RESOLDER JP17 UNDER LOPTX
Goodmans	1410	BLOWS 150V ZENER	RESOLDER JP17 UNDER LOPTX
GOODMANS	1410	DEAD	REPLACE RP41,42 AND 44 68K OHM
GOODMANS	1410	DEAD	REPLACE DP10 AND DP50
Goodmans	1410	DEAD	REPLACE RP41,42 AND 44
Goodmans	1410	DEAD	REPLACE DP10 AND DP50
GOODMANS	1410	DEAD S2000A S/C, BLOWS AFTER REPLACE	REPLACE LOPTX AND TRANSISTOR
Goodmans	1410	DEAD S2000A S/C, BLOWS AFTER REPLACE	REPLACE LOPTX AND TRANSISTOR
GOODMANS	1410	LINE TEARING WITH SQUEAK FROM CHOPPER TRANSFORMER	REPLACE CP90 22MFD50V
Goodmans	1410	LINE TEARING WITH SQUEAK FROM CHOPPER TRANSFORMER	REPLACE CP90
Goodmans	1410 TX805	Dead	CHECK RP 41 , 42 , AND 44 150k AND 120k IN PARALLEL.
Goodmans	1410 TX805	Dead	RP92 - 0.68 ohms
Goodmans	1410 TX805	Dead	DP18 ( BA159 ) RP68 ( 0.68ohm )
Goodmans	1410 TX805	Dead	D412 S.C. FITTED UNDER HEATSINK
Goodmans	1410 TX805	Distorted / Poor sound.	Check RA10 is correct ( 680ohm ) not 6K8.
Goodmans	1410 TX805	FIELD FLYBACK LINES	CHECK RES JP20 MARKED AS 680r 33r IN SET. SERIES WITH 100mfd
Goodmans	1410 TX805	Flyback lines.	Check resistor JP20 marked as 680R 33R in set. series with 100uf.
Goodmans	1410 TX805	INT SHUTTING DOWN OR DEAD	CHECK 15V SUPPLY RESISTORS
Goodmans	1410 TX805	Low brightness.	RT40 68K gone high , on CRT base.
Goodmans	1410 TX805	POOR SOUND , DIST.	CHECK RA10 IS COECT ( 680ohm ) NOT 6K8.
Goodmans	1410 TX805	Shutting down Int. or Dead.	Ck 15V supply resistors.
Goodmans	1410 TX805	Tuning drifts.	CHECK 33v DHO4 ZTK33 NEAR MAIN MICRO IC.
GOODMANS	1425RS	LINES ON BOTTOM OF SCREEN WHEN COLD	REPLACE C308 470MFD25V
Goodmans	1425RS	NO PICTURE SOUND OK	REPLACE C911 ON CRT BASE
Goodmans	1428T	LINE SPEED OFF	CHANGE TDA8362 TO A TDA8362A
Goodmans	1430/1404	STRIATIONS	REPLACE C420 ON CRT BASE
Goodmans	1430R	NO BAR DURING TUNING OR ADJUSTMENTS BUT FUNCTION WORKS	REPLACE IC602
Goodmans	1430R	No col & lack of height	R302 6k8 hi res
Goodmans	1430R Onwa	St/by only	IC301 pin 21 TA8718N 9v supply missing - R302 6k8 5w o/c
GOODMANS	1430RA	POWER COMES ON BUT NO PICTURE	CHECK ZD301 FOR S/C DIODBZX55B9V1 (9.1V)
Goodmans	1430RA (Onwa)	No col, lack of height/bottom cramp HT 112v as per manual	R302 6k8 in 8v startup supply hi res
Goodmans	1430RA (Onwa)	No sound no cursor on the baragraph	Don't replace the eprom! Disconnect pin 4 IC601, turn on and turn up the volume using the remote. When cursor and sound appear, resolder without turning off then hit standby on the remote to save!!
Goodmans	1430RW	DEAD RELAY CLICKING	C915 LEAKY
Goodmans	1430RWA	Dead - trips if on/off sw held in	C909/911 & lop tr 2SD2499 s/c (2SD1556 in lieu)
Goodmans	1435RS	FRAME COLLAPSE	CHECK R413 6.8K FOR O/C
Goodmans	1450T	LINES DOWN LEFT SIDE OF SCREEN	REPLACE C307 22MFD160V
Goodmans	1450T	NO TEXT	CHECK Q601 FOR DRY JOINTS
Goodmans	1450T	off burning smell	no line drive from AN5601 IC301. R323 8k2 in start up supply to chip o/c
Goodmans	1450T Onwa	Blank raster	cracked print rear edge of pcb removing supply to ZD102
Goodmans	1450T Onwa	Dead	4n7 500v disc cap across mains rect s/c & 4R7 5w o/c
Goodmans	1450T Onwa	St/by only	115v HT present. No supply to IC301 pin 42 due to R323 6k8 5w o/c
Goodmans	1450T Onwa	Tuning won't work	Crack in print of rear main pcb
Goodmans	1455	DEAD NO STANDBY LIGHT	REPLACE R913 220K OHM
Goodmans	1455TS	LOSS OF ONE COLOUR	REPLACE IC301 IC**AN5601
Goodmans	1455TS	SOUND CRACKLES INTERMTTANTLY	POSSIBLE ON/OFF SWITCH ARCING
Goodmans	1455TS	STUCK ON STANDBY WHEN COLD	REPLACE X601 4MHZ CRYSTAL
Goodmans	1455TS	Whistles int	C143 10µ front RHS near micro
Goodmans	145T	DEAD EXCEPT SBY LIGHT AND CHANNEL IND	R502/3 OC.330k
Goodmans	145TT	DEAD - 300v BUT NO START UP VOLTS	C 427 s/c 33mfd 50v ( START VOLTS BEING DROPPED ACROSS START RESISTORS )
Goodmans	145TTA	Dead	No volts pin 2 STR50103 reg - R502 330k o/c
Goodmans	145TTA	Dead zero voltage at pin 2 of the STR50103 regulat	Replace R502 ( 330k )
Goodmans	145TTA	St/by only	R502/3 330k start up res o/c
Goodmans	147	Dead ZD402 s/c R425 o/c	Check C911 & C909 Beware orientation of C909 should be "-" plate to Q904
Goodmans	147/149	Dead	SEE Bush 1400
Goodmans	147TT	Dead	ZD402 12v, R425 5R6 3w caused by C911 47µ 50v (may be inserted wrong polarity - marking on some boards is wrong)
Goodmans	147TT	DIST FIELD	R413 6k8 HIGH
Goodmans	147TT	NO VIS , BLANK RASTER ( MAY RE-APPEAR WHEN A1 ADJ.	R430 180k
Goodmans	148	WONT STEP UP CHANNELS INT ( ALSO OTHER ODD EFFECTS	CHANGE MEM ICs ( BOTH ) IC**CAT24C02P
Goodmans	148T	ROLLING AND PULLING PIC.	CHECK C703 47nf
Goodmans	149TT	Dead ZD402 s/c R425 o/c	Check C911 & C909 Beware orientation of C909 should be "-" plate to Q904
Goodmans	149TT	Field collapse	R375 180k o/c (connected to pin 33 AN5601 IC301)
Goodmans	14RC 20RC	LOW CONTRAST/ COLOUR	R241 ( 150k ) NEAR SCAN PLUG
Goodmans	2019R	MILKY OR STREAKY PICTURE	REPLACE ZD301 5.1V ZENER
Goodmans	2019R Onwa	High contast - wont reduce	7.5v on 5v supply to micro - Q615 leaky
Goodmans	2019R(Onwa)	Poor contrast after replacing usual caps & 12v zener	IC301 AN5601K col dec chip
Goodmans	2025RS	DEAD WITH NO STANDBY LIGHT POWER SUPPLY RUNNING	REPLACE IC1802
Goodmans	2025RS	THREE COLOUR RINGS COVER ENTIRE SCREEN	REPLACE IC301
Goodmans	2028T/2195T	LOCKED UP WITH NO CHANNEL CHANGE	REPLACE XT01 27MHZ CRYSTAL
Goodmans	2029T	BLANK RASTER WITH NO SOUND	CHECK C113 0.01MFD FOR S/C
Goodmans	2040R	Dead StBy LED lit relay clicks when r/c pushed	R803 ( 390K ) pin 3 IC 801 o/c
Goodmans	2043T	Black blobs on top sides of screen	C406 1µ 160v in line scan coupling
Goodmans	2043T	Dark with high col content & tuner drift	12v supply at C429 only 8v. R437 & R427 hi res - fit 1R5 1w types
Goodmans	2043T	Dead	C805P 100µ 16v in psu
Goodmans	2043T	DEAD	CHECK D8035 FOR O/C LOCATED OFF PIN B OF LOPTX
Goodmans	2043T	Dead - HT ok at pin 17 of chopper tfmr	No HT at B+ of loptx - D8035 o/c
Goodmans	2043T	DEAD HT LOW	REPLACE C8075
Goodmans	2043T	DEAD POWER SUPPLY OK	D8035 OC
Goodmans	2050R	Line down pic when cold (folded scan)	R413 18R ½w hi res - check HT correct -115v 14/20"; 109.5v 15/21"
GOODMANS	2050T	CHILD LOCK	TO REMOVE HOLD P+ WHILE TURNING ON POWER
Goodmans	2050T	CHILD LOCK	TO REMOVE HOLD P+ WHILE TURNING ON POWER
Goodmans	2052T ONWA	Stuck in standby.	C910 ( 100uf , 160v ) in LTB.
Goodmans	2053T	NO ON SCREEN DISPLAY TEXT BAR STILL PRESENT AT BOT	10 Mhz CRYSTAL ON IC 702
Goodmans	2055	SEARCHES PAST STATIONS , NO STATION IDENT.	TDA8362B
Goodmans	2055T	Int Loss of pic No Text	27Mhz crystal on Text PCB
Goodmans	205N	poor field lin & tuning drift	8v reg I402 faulty (running hot)
Goodmans	205N	St/by only	Replace C811, 812, 813 & check HT is 103v at relay
Goodmans	206NS	Blank raster, no sound, osg or r/c when first switched on (OK after re-switched on)	Earth speakers/grill to crt rimband
Goodmans	206NS	DEAD. F801 BLOWN	IC801 REGULATOR FAULTY
Goodmans	206NS	LINE TEARING AFTER WARM UP	POSSIBLE DRY JOINTS ON IC501
Goodmans	206NS	NO GREEN ON TELETEXT PICTURE OK	REPLACE D702 1N4048
Goodmans	20XRT	No contrast Adj	Check V at pin 6 TDA3562 should vari with Contrast if not check R414 ( 33K ) o/c
Goodmans	2143	SHUTS DOWN OR DEAD	C804P 8n2
Goodmans	215N	AUDIO BUZZ FROM BOTH CHANNELS	RESOLDER FRAME IC HEAT SINK
Goodmans	215N	GREY SCALE OK UNTILL COLOUR INCREASED THEN SCREEN GOES PINK	REPLACE IC501 TDA8362
Goodmans	215N	Lock out all buttons & handset inoperative	Replace IC710 ( SN76861NJ12 )
Goodmans	215N	NO CHANNEL CHANGE WITH REMOTE OR FRONT BUTTONS	REPLACE 13.89MHZ CRYSTAL
Goodmans	215N/2055	UNDER OR OVER SCAN AFTER LOPTX REPLACED	DCF2217L REQUIRES DAEW50H0000121 AND DCF2217J REQUIRES DAEW50H0000124
Goodmans	2170 2180 2175	Hooking at top when playing Video	Fit ( 1uF ) in place of C287 ( 2170 2180 ) & C233 ( 2175 2185 )
Goodmans	2170 / 2180	Dead	Check R105 150k, R106 150k, R107 270k & R108 270k
Goodmans	2170R 2180	Will not go into StBY	CHECK R105 R106 180k
Goodmans	2175 2185	Will not go into StBy	Replace R102 & R103 ( 150K )
Goodmans	2175R	Field foldover of about two inches.	C333 ( 4.7uF , 1
Goodmans	2175R	Field top foldover	C333 4µ7 160v
Goodmans	2175R	GREEN SMEARY PICTURE	R619 330K ON CRT BASE OC
Goodmans	2175RA	Colours flash as it warms up leaving red	R620 220k cathode curr measurement res on crt base
Goodmans	2180	Dead	R105 106 150k R107 108 270k NEAR OPTOCOUPLER
Goodmans	2180	Dead.	Check R105 ( 150k ) , R106 ( 150k ) , R107 ( 270k ) , R108 ( 270k ) by CNX82 in PSU
Goodmans	2180	No S/V line hum blank raster	C216
Goodmans	2185	Dead 300V at pin 3 STK54041	Check R104 ( 270K )
Goodmans	2185	DEAD WITH LINE O/P TRANSISTOR S/C	REPLACE C264 47MFD160V
Goodmans	2185	LOW FIELD/WIDTH , HUM ETC.	HT SMOOTHING O.C. 220 mfd , 200V
Goodmans	2185T	dead	st/by light goes out at sw on - R104 270k o/c in start up cct - R105 & 106 can also be responsible
Goodmans	2185T	Dead	R104 270k o/c
Goodmans	2185T	Field cramping	C333 4µ7
Goodmans	2185T	Green pic	R618 470k o/c ( covered in gunge)
Goodmans	2195 , 205N , 215N	NORMAL SETTINGS , AMBIGUITY IN USER INSTRUCTIONS ,	STORE WITH STORE AND RETURN TO NORMAL BY PRESSING "MENU" TWICE. ---- USING "TV" TO EXIT DOES NOT WORK , THIS IS IN EFFECT
Goodmans	255NS	WEAK CONTRAST AND POOR SYNC ON AV2	REPLACE DA18
Goodmans	256NS	Dead & whistling	C2912 blue disc cap 2n2 2kv leaky
Goodmans	256NS	E-W dist	capacitor 2913 (390n 250v) and 7908 (STP4NA40F1 mosfet)
Goodmans	256NS	No E/W correction & low width	390 nF 250 v cap ( ref 2913 ) big blue cap on the E/W board
Goodmans	2575	DEAD , TRIES TO START.RED LIGHT FADES AND PULSES DIE	RUN DIODE D35 , PRIMARY OF s Mode BA157
Goodmans	2575	SEVERE BLACK BANDS ACROSS PICTURE SOUNDS LIKE LINE	TUNER ( PLUG IN SCART PLUG TO PROVE )
Goodmans	2575	WON'T SWITCH ON FROM COLD	REPLACE C102 IN POWER SUPPLY
Goodmans	2575 2875	INT BRIGHTNESS VARYING	CHECK A1 SUPPLY , POSS LOPT
Goodmans	2575 2875 33	LOOKS LIKE ONE COLOUR OVERDRIVEN	CHECK R26 / 28 / 29 ON CRT BASE. 68K 0.5W. NORMAL VOLTS AT RGB PINS OF TDA8361A / TDA 8362A IS ABOUT 2.5v
Goodmans	2575 2875 3375	INT START UP	CHANGE R19 FROM 1k2 TO 4k7 ( LOCATION IC1 PIN 33 ACROSS D9 )
Goodmans	2575 2875 3375	Rope effect 3" from LHS	Replace line drive TR
Goodmans	2575 2875 33	REPLACING NICAM BOARD CONTAINING SAA7280 WITH SAA	Remove link J103 & fir 22R 12V supply to Nicam & fit ( 100uF ) 16V cap across CRT base plug "+" to pin 1 "-" to pin 6
Goodmans	2575 / 2875 / 33	LOOKS LIKE ONE COLOUR OVERDRIVEN	CHECK R26 / 28 / 29 ON CRT BASE. 68K 0.5W. NORMAL VOLTS AT RGB PINS OF TDA8361A / TDA 8362A IS ABOUT 2.5v
Goodmans	2575 / 2875 / 33	REPLACING NICAM BOARD CONTAINING SAA7280 WITH SAA	Remove link J103 & fir 22R 12V supply to Nicam & fit ( 100uF ) 16V cap across CRT base plug "+" to pin 1 "-" to pin 6
Goodmans	2575 2875	INT BRIGHTNESS VARYING	CHECK A1 SUPPLY , POSS LOPT
Goodmans	2575 2875 3375	Blank raster Intermittently	D44 leaky BA157 replace with 1N4007
Goodmans	2575TV	dead	dry joints link 13 on main pcb
Goodmans	2580(TX92)	LINE TEARING AFTER SET WARMS UP	CHECK EHT LEAD IS FULLY SLOTTED INTO LOPT
Goodmans	2595TN	Will not go into StBY	Replace R105 & R106 ( 150K )
Goodmans	285DPL	ARCING ON PICTURE	RESOLDER LINE O/P TRANSISTOR HEAT SINK
Goodmans	285DPL	BLANK RASTER WITH SOUND	REPLACE C416,R409,R503 AND D506
Goodmans	285DPL	DEAD WITH STANDBY LIGHT FLASHING	REPLACE RK68 AND VK71
Goodmans	285DPL	EHT COMES UP THEN SET SHUTS DOWN	SUSPECT LOPTX
Goodmans	285DPL	LACK OF WIDTH WITH E/W DISTORTION	CHECK RK62 FOR DRY JOINTS
Goodmans	285DPL	LED FLASHES 3 TIMES THEN STAYS ON SET DEAD	REPLACE VK71 AND NS10
Goodmans	285DPL	NO SOUND FROM HEADPHONE SOCKET	CHECK HEADPHONE LEVEL IN SOUND MENU
Goodmans	285DPL	POWERS UP THEN GOES TO STANDY	VK67 ON PIN 3 OF LOPTX S/C
Goodmans	285DPL	PUTTING NOISE ON STANDBY	REMOVE LINK WA21 ON DOLBY MODULE
Goodmans	285DPL	St/by only	timing constant capacitor for the standby IC is leaky. The IC is mounted on a heatsink in the middle of the board. C093 is a pair of surface mount capacitors [in parallel] connected between pins 2 and 4 of the IC. Remove these capacitors and replace them with a 220nf.
Goodmans	285DPL	STUCK IN STANDBY	CHECK VK51 BY228 AND VK61 BYW74 FOR S/C
Goodmans	285DPL	TICKING NOISE FROM FOCUS UNIT AND PICTURE OUT OF FOCUS	CHECK FOR DRY JOINTS ON RK61
Goodmans	285NS	CABINET RATTLE	REMOVE SPEAKER GRILLS AND FIT FELT
Goodmans	285NS	CAUSING TIMER PROBLEMS WITH SOME VCR'S	REPLACE MICRO
Goodmans	285NS	FULL VOLUME	I702 EEPROM FAULTY
Goodmans	285NS	LINE FOLDOVER AND EXCESIVE WIDTH	REPLACE C416 BLUE 2KV TYPE
Goodmans	285NS	Pic slow to come on - sound ok	Replace TDA8375A jungle chip
Goodmans	285NS	Trips once then dead	s/c on 12v supply to tuner - MCES will repair
Goodmans	285NS	Various faults on chan change; eg E-W, blank raster or snow or st/by	data line down to 4V (must be 5V) - D708 5.6V zener is leaky Also replace D709 5.6V zener to be on the safe side.
Goodmans	285NS (Daewoo)	To set up height	Reqs special handset
Goodmans	285NS (B)	BLANK RASTER SOUND OK THEN PICTURE APPEARS AFTER 20 MINS	REPLACE JUNGLE IC
Goodmans	285NS(B)	DARK PICTURE WHEN USING SUBTITLES	SELECT TEXT THEN PRESS MENU AND ADJUST BRIGHTNESS LEVEL
Goodmans	285NSB	Dead - mains fuse blown	Positor faulty - rattled & pic shifted to left until replaced
Goodmans	286N5/05	Service Mode access	call up the main menu then press 2,3,5,7, quite quickly on the remote. To get to geometry settings press * (star).if the EEprom is relaced with a blank one, as supplied by SEME, the picture geometry settings have to be adjusted for each different "display" setting (aspect ratio)
Goodmans	286N5/05	Tries to start up then trips	Tr75055 BC337
Goodmans	286NS	DEAD NO POWER LED	REPLACE C2915
Goodmans	286NS	FRAME COLLAPSE	R3908 O/C 2R2
Goodmans	286NS	PARTIAL FRAME COLLAPSE	REPLACE R3988 2.2OHM FUSABLE
Goodmans	286NS	STUCK ON STANDBY	REPLACE FUSABLE 1502 BESIDE SMPS TRANSFORMER POSSIBLE ICFN25
Goodmans	286NS (Philips L6.3 chassis)	No sound - noise only from speakers	MPS3410 chip faulty - replaced audio pcb
Goodmans	286NS/05	F o/p tr overheats	Field scan coils shorted turns
Goodmans	286NS/05	Goes in & out of st/by at sw on	Transistor 7505 BC337-40 (5v reg tr)
Goodmans	2875	E.W. FAULT	CHECK 10nf , HA POT , DIODE
Goodmans	2875	LINE TEARING THAT CLEARS AFTER A FEW MINUTES	REPLACE C123 IN POWER SUPPLY
Goodmans	2875 (F11)	Dead with TR15 S2000N S/C	Replace S2000N and C102 100ufd which was down to 20ufd
Goodmans	2875 F11	Dead stuck in st/by	R170 O/C safety resistor from secondary off chopper transformer due to IC8 TDA1521 audio output S/C.
Goodmans	2875 F11 chassis	Won't sw back on after st/by selected	Check all elects in psu pri
Goodmans	2876 F11 chassis	Low emission crt symptom	Check feedback res R26, 28 & 29 68k on crt base
Goodmans	2880	FRAME COLLAPSE NOT IN CENTRE OF SCREEN	REPLACE TP91 BC848B AND TP96 BC858B IN POWER SUPPLY
Goodmans	2880	PURITY PROBLEMS	CHANGE VALUES OF RP40 AND CP40
Goodmans	2880 (ICC9)	2 INCH BAR OF SNOW AROUND BLANK SCREEN	REPLACE TR42
Goodmans	2880 (ICC9)	INT FRAME CRAMPING	REPLACE DF31