Home Up What's New Index of Web Site Radio Rig Mods Radio Rallies Ham Radio Hobby CW Facts DX Calendar Search Page Earth Project Club Members Welsh Links Radio Links 1 Radio Links 2 What's New TV Sky Codes Sky Codes 2 Sky+ AV Amp TV DataBase



 

     Mitsubishi Euro  

BRIDGEND & DISTRICT AMATEUR RADIO CLUB
 GW4LNP/GC4LNP
 

Home Up What's New Index of Web Site Radio Rig Mods Radio Rallies Ham Radio Hobby CW Facts DX Calendar Search Page Earth Project Club Members Welsh Links Radio Links 1 Radio Links 2 What's New TV Sky Codes Sky Codes 2 Sky+ AV Amp TV DataBase

 


 
TV Repair Database
 
Mitsubishi EE2 black line down lh side R571 560R 1w o/c
Mitsubishi EE3 Bank raster/no sound - OSD ok Z953 1.6A cct prot. Has been uprated to 3.15A in sets incorporating sat Rx
Mitsubishi EE3 Crushed whites Q952 8v reg dry joints
Mitsubishi EE3 Dead AVN5-KIT is available when Q552 has gone s/c - includes R713 1k, R726 5k6, Q552 2SD1556, Q901 S2000N, R508 3k9 5w, R991 4R7 10w, D909 RD3.0FB2 zener, an additional cap  C720 22pf
Mitsubishi EE3 Dead Cct prot o/c - uprated to 3.15A from 2A also could be start up res R915 15R 2W, R922, R921 & R902 22k 2w 
Mitsubishi EE3 Dead - LOP tr S2055N leaky then no line dr Q551 fully conducting, Q501 JC501-R u/s
Mitsubishi EE3 Dead - Q552 s/c due to high hT C914 47µ 35v o/c
Mitsubishi EE3 Dead apart from flashing red/green LEDs C955 1000µ 16v
Mitsubishi EE3 Dead- initially long time to come on C914 47µ 35v, C955 1000µ 16v
Mitsubishi EE3 Dead; 2A fuse blown violently & chopper Q901 s/c Replace Q901 S2000N, IC901 TEA2261, Opto coupler PC951 TCDT1124G. Check D909 zener RD3.0FB2 & R908 0R33 2w & R909 0R22 2w
Mitsubishi EE3 Green LED lit - no other activity HT secondary supplies ok- no line drive. IC702 EEPROM may need reprog
Mitsubishi EE3 grey scale varies CRT bias request bit could not be set to 00 with G2 control - not IC201 dec/tbase gen chip.Cured by replacing TEA5101 RGB o/p chip & diodes D655/6/7 1N4148 on crt base
Mitsubishi EE3 Lock up & memory problems Replace C955, C702 & R3D68 also change value of R702, R213 & R214 to 1k ¼w
Mitsubishi EE3 long time to come on C955 2200µ for 11.5v supply
Mitsubishi EE3 Low contrast, smeary, f back lines R686 on crt base (1k8)
Mitsubishi EE4 Dead or int dead - brief flash of green led at sw on Dry joints opto isol PC951
Mitsubishi EE4 Trips once at sw on - ok on dummy load TEA5101B RGB o/p chip IC660 s/c
Mitsubishi EE4 (M5 models) To enter service mode Press & release S701 next to aerial socket, then press "9" on hset within 5 secs. Buttons 2 & 8 select adj code, buttons 4 & 6 adj data value. Button 1 cancels written data, button 0 stores data into EEPROM see article TV Jan 99 for more details
Mitsubishi Euro 1 Diagonal pattern of dots across screen R914 100R in psu snubber cct o/c
Mitsubishi Euro 10 Black lines , poor sync, no txt (until warm) C959, 962 100µ
Mitsubishi Euro 10 Dead C905 470µ 25v
Mitsubishi Euro 10 Dead - Q901 chopper tr blows at sw on D909 3v zener s/c was the cause; also replaced R901 4R7 5w, IC901 TEA2164
Mitsubishi Euro 10 dead psu runs several electrolytics in psu leak electrolyte onto plug PB causing o/cs
Mitsubishi Euro 10 Field jitter - int Dry joint R461
Mitsubishi Euro 10 Field lin faulty when cold Glue around pins of IC501
Mitsubishi Euro 10 HT low Q953 JC501Q error amp
Mitsubishi Euro 10 int dead (could be ok for days) Same on dummy load proving psu fault. Opto coupler driver tr Q953 was to blame. BC547 suitable replacement
Mitsubishi Euro 10 Int dead esp from cold C905 220µ, C906 47µ  C912 4µ7 in psu
Mitsubishi Euro 10 Int loss of sound & pic Check vid I/p & o/p at AV sw chip IC2A2 M5132P - if no o/p either off air or scart this chip is sus; if o/p with scart but not off air sus Q2A2. If no pic but sound ok check Q104
Mitsubishi Euro 10 Int sw on from cold C905 470µ 25v in start up cct
Mitsubishi Euro 10 Loses analogue memory when sw off The -30v to IC702 memory chip low due to C962 100µ 50v
Mitsubishi Euro 10 Loud whistle from psu - set operates ok otherwise Q902
Mitsubishi Euro 10 No pic - OSG & sound ok No 5v reg supply to VIP & CCT chips as Z951 630mA cct prot o/c
Mitsubishi Euro 10 No sound Q952 2SA950-Y leaky
Mitsubishi Euro 10 No sound No lt supply to audio chip - Q952 2SA950 o/c; BC640 used in lieu
Mitsubishi Euro 10 No sound/pic - no memory & slow R/C response IC702 EEPROM chip ST24C02A
Mitsubishi Euro 10 not memorising user prefs C962 100µ on -30v supply
Mitsubishi Euro 10 Patterning - clears with a bang on cabinet IC902 12v reg faulty
Mitsubishi Euro 10 pic fluctuate after few secs HT low at 107v (112v) C906 47µ 25v also replaced C905
Mitsubishi Euro 10 Poor contrast Q704 JC501 blanking tr on main pcb
Mitsubishi Euro 10 Popping noise fro speakers in st/by ; 20v supply not being sw off Q5951 JC501-Q faulty or dry jointed, Q952 2SA950-Y, R954, R974 or R985 can also be responsible 
Mitsubishi Euro 10 Sound dist IC361 AN5264 audio o/p chip dry joints
Mitsubishi Euro 10 St/by only after being int for previous 2 days Dry joints LOPTr Q552 2SD1878
Mitsubishi Euro 10 Switches off immediately after powering up Check PC951 opto coupler
Mitsubishi Euro 12 Black box appears on screen &/or no TXT C958 1000µ 16v in 5v supply
Mitsubishi Euro 12 Blue excessive (or Green/Red) D656 leaky on crt base ( or D655, D657)
Mitsubishi Euro 12 Contrast low with fb lines IC251 pin 7 only 1.2v instead of 2.9v; 12v line low as Q704 leaky
Mitsubishi Euro 12 Dead Q552 2SD1878 s/c; R901 4R7 10w o/c
Mitsubishi Euro 12 Dead - blows Q901 C906 47µ 50v
Mitsubishi Euro 12 Dead - Chopper Q901 & lop tr Q552 u/s Q901 serv kit fitted & Q552 2SD1878 also C905 470µ 35v, C906 47µ 50v, C909 2µ2 50v, C920 100µ 25v
Mitsubishi Euro 12 Dead - LOPTr s/c due to High HT Check R961 150k & C906 47µ 50v & IC950
Mitsubishi Euro 12 Dead - off with bang C906 47µ 63v, Q901 2SD1887, R901 4R7 10w, IC901 TEA2261, D907/8 RD3.0FB1, C920 100µ 63v - C975 47µ 63v was the cause
Mitsubishi Euro 12 Dead apart from 3 chirps at sw on LOPTr 2SD1878 s/c also replaced C956 47µ in psu
Mitsubishi Euro 12 Dead or Int reverts to st/by - LOPTr Q522 fails periodically  - possibly due to high HT C906 47µ 50v drive coupling cap - also check C905 470µ 35v, C909 100µ 25v,C920 100µ 25v, R961 150k, R972,  R960, D907 RD3.0 s/c &  IC950; Q522 = 2SD1877 (21"), 2SD1878 (25"), 2SD1879 (29")
Mitsubishi Euro 12 Dies at sw on with squealing C956 1000µ 35v, C958 1000µ 16v, C964 1000µ 50v leaky & dry joints & IC551 (e/w chip) & TEA2031A damaged
Mitsubishi Euro 12 Excess width TEA2031A
Mitsubishi Euro 12 Excess width, bowed verts & pic shifted sideways Low amp H SYNC fback pulse from LOP - D559 1N4148 s/c - check for dry joints LOPTx
Mitsubishi Euro 12 Field collapse No 28v to TDA8178S - R976 0R82 in psu o/c
Mitsubishi Euro 12 Field collapse Replace chip - must be same suffix - use Phoenix repair kit from Grandata
Mitsubishi Euro 12 Field collapse Replace TDA8178S & check C956 1000µ 35v, C452 220µ 25v & HT - Mitsi mod kit 2 available from Grandata (cheaper)
Mitsubishi Euro 12 Field collapse IC451 TDA8178S (must use correct one or foldover occurs if TDA8178FS is used - very expensive!) Also check C452 220µ 35v & 122v HT at TP91
Mitsubishi Euro 12 Freq blows SD1887 sw mode transistor Mod kit avail from WVE (Q901 modkit) & change TEA2261
Mitsubishi Euro 12 High HT - should be 120v C906 47µ 50v, C909 2µ2 50v & 2 x 3v zener diodes D907 & 908
Mitsubishi Euro 12 Hum in st/by & no degaussing C960 1000µ 35v in 24v supply
Mitsubishi Euro 12 Int blows Q552 Dry joints T551
Mitsubishi Euro 12 Int Field foldover/lack of height - Low HT at 87v No set HT control, crack in print between base Q952 & R956/7 junction
Mitsubishi Euro 12 Int Nicam crackling - tuner drift Dry joints IF unit esp on SAWFs & coils
Mitsubishi Euro 12 Int sound/pic - comes & goes with a tap Dry joints IF can
Mitsubishi Euro 12 Int sound/pic - comes & goes with a tap Dry joints VIF module
Mitsubishi Euro 12 Lines on pic with whistling C956 2200µ 16v in psu
Mitsubishi Euro 12 Luminance int Q202 J501Q
Mitsubishi Euro 12 No audio pback from mono VCR or sat Rx IC702 EEPROM (new one needs reprog) or get kit IC702-KIT; pt no of chip = 263P434020
Mitsubishi Euro 12 No signals aft 5 mins Dry joints 4Mhz Xtal in prescaler
Mitsubishi Euro 12 No signals or tuning Check IC955 30v reg or feed res R951 - could also be C102 0µ01 25v
Mitsubishi Euro 12 No sound/pic red led then green one come on & both then go out D909 4v3 zener
Mitsubishi Euro 12 No Txt & pic shifted to one side IC702 EEPROM (new one needs reprog) or get kit IC702-KIT - pt no of chip = 263P434020
Mitsubishi Euro 12 North/South distortion Q4009 2SA950 on N/S correction panel
Mitsubishi Euro 12 Pic int lost Q702 JC501QR faulty in micro's cct - BC182L works ok in lieu
Mitsubishi Euro 12 Pic too large - no Txt or Nicam - happens aft blow up repair Mod kit IC702 reqd (IC702 & 2 x 6k8, 1 cap)
Mitsubishi Euro 12 PSU blew again aft rebuild ZD908 3v zener s/c (In parallel with 2 x 0R25 res)
Mitsubishi Euro 12 Rolling/Unstable pic 12v supply high at 15v - D958 1N4148  (pins 4 & 5 of reg IC951)
Mitsubishi Euro 12