Home Up What's New Club History Index of Web Site Radio Rig Mods Radio Rallies Ham Radio Hobby Radio Beacons DX Calendar ATV Links ARRL Links CW Facts Earth Project Club Members Radio Links 1 Radio Links 2 What's New TV Sky Codes Sky Codes 2 Sky+ AV Amp Welsh Links



 

     Philips FL1.17  

BRIDGEND & DISTRICT AMATEUR RADIO CLUB
 GW4LNP/GC4LNP
 

Home Up What's New Club History Index of Web Site Radio Rig Mods Radio Rallies Ham Radio Hobby Radio Beacons DX Calendar ATV Links ARRL Links CW Facts Earth Project Club Members Radio Links 1 Radio Links 2 What's New TV Sky Codes Sky Codes 2 Sky+ AV Amp Welsh Links

 

 
TV Repair Database
 
Philips FL1.17 "NVM write protection enabled" message on screen. Startup problem or 'NVM write protection enabled' message on screen
after replacement of NVM
 (ST24C08CB1; 4822 209 32283) with a ST24C08CB6 (4822 209 33113).

Use as replacement the ST24C08 1 (9311 021 36682).
Philips FL1.17 100Hz cross Possible solutions:
1. Interrupt on the SSP the 50Hz Y-signal, between pin 11 position
   IC7324 (TDA4568) and pin 11 position IC7395 (TDA8443), by       
   deleting position 4302.
   Repair the connection by means of a shielded cable of 16cm long,
   m
Philips FL1.17 22AV1440 is switched on by external VCR when FL1 is switched off Connect 4 diodes of type BAT 85 to inputs of IC7630 on SSP.
1 diode between pin 3/IC7630 and +5V, cathode to +5V.
1 diode between pin 5/IC7630 and +5V, cathode to +5V.
1 diode between pin 3/IC7630 and -8V, anode to -8V.
1 diode between pin 5/IC7630 and -8
Philips FL1.17 50Hz buzz noticable through speaker Check/replace IC7680 on the SSP - TDA8425, pseudo stereo IC.
(4822 209 63734).
 
Philips FL1.17 Adaption of Service Information FL93.05 Adaption of Service Information FL93.05
---------------------------------------
From 93-06-24 onwards the definition of optioncode 4 has been
changed.
From this day onwards the definition is as follows:
1    TXT peaking filter on/off for LFR box (Scandina
Philips FL1.17 After 10 minutes picture becomes red from right side C2395 on the LSP poorly soldered.
 
Philips FL1.17 After about 10 min. cracking noise from the right tweeter. Cracking signal from pin 6 of IC7009 (LM833N) on LSP
(4822 209 83163)
 
Philips FL1.17 Antenna input: no sound. External input: sound O.K. Check whether crystal 1602 (stereo decoder) 10MHz oscillates.
If not replace X1602 (4822 242 80276).
 
Philips FL1.17 Bad focus or focus varies in a new set or after CRT replacement Possible solution:
Short circuit the focus and the G2 pins of the picture tube with the
aquadag coating. Switch the set on for approximately 5 seconds.
After this return the set to its original condition. Check if the
focus adjusted normally. If not repla
Philips FL1.17 Bad pict. No menu. Dark bars over pict. Red pict. in dig.scan mode. +5V was 4,3V instead of 5,1V.
IC7551 (LM358N  4822 209 70672) defective.
IC7209 (SAA7158 4822 209 31059) Bendic defective.
 
Philips FL1.17 Bad picture. Picture scrolls. No RC reaction. +5V was 4,1V instead of 5,1V. Replace IC7551 (LM358N; 4822 209 70672)
 
Philips FL1.17 Bad synchronization with external signals Delete position 3115 on the ECO 100Hz box.

REMARKS          :
Introduced in production in week 9415.

 
Philips FL1.17 Blank picture. OSD not synchronised and too large, no TXT. Check/replace memory IC 7900 (ST24C08CB1; 4822 209 32283).
 
Philips FL1.17 Both languages can be heard by Dual Nicam signals For FL1-PTV change the software into V89; 4822 900 10732
For all other FL sets change the software into V88; 4822 900 10723

REMARKS          :Introduced in production from week 9614 onwards.
Philips FL1.17 BUX85F in mikroSOPS defective Change the value of C2260 to 4n7F, replace 7270 with transistor
BD825 (4822 130 41746).
 
Philips FL1.17 Colored picture or picture is green/red, fly-back lines Check zenerdiode 6450 on pin 19-IC7430 on the LSP. New diode must
be Philips (Telefunken does not work), 4822 130 81512 
 
Philips FL1.17 Colour loss at photofinish and scan. Change position 6003 on the ECO-box into a LL4148 (4822 130 80446).

REMARKS          :
Introduced in production in week 9424.
Philips FL1.17 Correction to Product Survey 1996-4 Correction to Product Survey 1996-4 (4822 727 21505)
----------------------------------------------------
On page PCS 41989 is mentioned at:
FL1.10    AG11 and higher: Control panel 4822 212 31708
FL1.17    AG20           : Control panel 4822 212 31708
FL
Philips FL1.17 Correction to service information FL 95.01 Correction to service information FL 95.01
------------------------------------------
Correction in the overview of 100Hz and Proscan boxen.

The replacement for service code 4822 212 30534 must be 4822 212 31231
The replacement for service code 4822 21
Philips FL1.17 Correction to Service Manual Correction to Service Manual
----------------------------
In service manual FL1/2.14, FL1/2.16, FL1.17 AA the code number of
the Scavem amplifier panel is wrong. The correct code number for
this panel is 4822 212 31469.

REMARKS          :
The code number
Philips FL1.17 Correction to service manual FLx.14/16/17 Correction to service manual FLx.14/16/17 and FLx.24/26/27.
-----------------------------------------------------------
The code number of position 1200 (fuse 3,15 A) is wrong.
The correct code number is 4822 070 33152. This fuse is situated on
the LSP i
Philips FL1.17 Correction to the Service Manual Correction to the Service Manual
--------------------------------
In circuit diagram B on page 7 of the service manual
FL1.14/FL2.14/FL1.16/FL2.16 and FL 1.17 the resistors 3624 and 3625
are not drawn.
These resistors should be drawn on the position of 96
Philips FL1.17 Crazy behaviour: No response from RC or controls. Other phenomenas: volume up/down, spontanuous service mode etc.
etc. in areas with TOP-teletext.

Replace control software by replacing EPROM IC7002 to version V82
(4822 900 10423). For easy mounting also the controlboard 7115
(on SSP) can be replaced by 
Philips FL1.17 Crazy behaviour: No response from RC or controls. Other phenomenas: volume up/down, spontanuous service mode etc.
etc. in areas with TOP-teletext.

Replace control software by replacing EPROM IC7002 to version V83
(4822 900 10506). For easy mounting also the controlboard 7115
(on SSP) can be replaced by 
Philips FL1.17 Crazy behaviour: No response from RC or controls. Other phenomenas: volume up/down, spontanuous service mode etc.
etc. in areas with TOP-teletext.

Replace control software by replacing EPROM IC7002 to version V83
(4822 900 10506). For easy mounting also the controlboard 7115
(on SSP) can be replaced by 
Philips FL1.17 Dark picture, only green led, no menu or OSD. +5V supply was 4,1V. Voltage D6551 was 4,3V instead of 5,6V.
Check/replace D6551 (4822 130 80954).
 
Philips FL1.17 East/West failure in cold condition. Replace C2611 by 1uF (4822 121 51319) on LSP. 

REMARKS          :
Introduced in production in week 9332.
 
Philips FL1.17 Fall off position 3204 on the Large signal panel Fall off position 3204 on the Large signal panel
------------------------------------------------
When position 3204 (NTC/PTC; 4822 116 40215) on the LSP is defect it
is recommended to replace it by a PTC/PTC (4822 116 40253).
Together with this change al
Philips FL1.17 Four dark bars over the picture. The +5 volt was 5.6 volt instead of 5.1 volt.
Check/replace IC7551 (4822 209 70672).
 
Philips FL1.17 How to enable/disable "Child Lock" Press "MENU" button on Remote Control. When the menu appears on the
screen, you select "SPECIAL FEATURES" (this expression is language
dependent)
Within "SPECIAL FEATURES", the "CHILD LOCK" can be enabled or
disabled.
 
Philips FL1.17 Inoperative. Only stand-by led on. Default gives: 00 00 00 99 Check Line Transistor T7504, T7506 (ON4673C; 4822 130 62134).
 
Philips FL1.17 Inoperative. Only stand-by led on. Hardware protection. Check zenerdiode D6376 (LLZ-C20; 4822 130 81143).
 
Philips FL1.17 Jitter In PIP unit change the value of R3336 to 4k7.
 
Philips FL1.17 Jitter at NTSC reception. Replace item 9459, connected to pin 13 of IC7400 on the LSP, into
220 ohm (4822 116 52215). 

REMARKS          :
Introduced in production in week 9335.
 
Philips FL1.17 Low Brightness TXT and OSD, Picture OK If this condition occurs, check the Option Codes.
Resetting the Option Code numbers as per the Service Manual provided
the cure.
 
Philips FL1.17 Low frequency hum from subwoofer, buzz from right hand squeeter. Check DC level on pin 1 and 9 of IC7011 (TDA1521).
If not correct, replace (4822 209 63913).
 
Philips FL1.17 Modification Modification
------------
Only for 25"

During production in week 9405 the picture tube of the 25" sets has
been changed from the A59EAK252X43 (4822 131 20501) into a
A59EAK252X44 (4822 131 20602). This new picture tube is used in
sets with serial number 
Philips FL1.17 Modifications of service manual FL1.17 Modifications of service manual FL1.17
--------------------------------------
- item 2405 changed into 18nF 63V      (4822 122 31759)
- Item 3404 changed into 3k3 0,25W     (4822 051 10332)
- item 3624 and 3625 added 22 Ohm 0,5W (4822 116 52186)
- item 96
Philips FL1.17 No colors in TV mode Check IC7365 (TDA4650) on the SSP (4822 209 30837)
 
Philips FL1.17 No colour after 1 hour. Pin 7S22 output 100Hz box is 6V instead of 12V. 
Check T7127 (BC858; 5322 130 41983).
 
Philips FL1.17 No colour. Menu, OSD, TXT are O.K. Check 5.1V supply voltage on IC7201/7202 on ECO-box. If too low
check zener D6026 (BZV55-A5V1; 4822 130 83459).
 
Philips FL1.17 No sound, "ON, Standby, I" LEDs blinking 10MHz crystal 1602 on the SSP defective, 4822 242 80276
 
Philips FL1.17 Noise on high volume Perform the following modifications on the SSP:
Add on position 3618 4,7nF (4822 122 31784)
Add on position 3619 jumper (4822 051 10008)
Connected in series from 2604/4610 to earth.
Change position 4610 into 1k ohm (4822 051 10102)
Philips FL1.17 Noisy green picture. No B-Y signal. Check IC7245 (SAA4970T/V1; 4822 209 32581) on ECO-box.
 
Philips FL1.17 Only for Classic Line Correction of Product Survey Only for Classic Line

Correction of Product Survey 1993-3
-----------------------------------
The stocklist of styling 31 in Product Survey 1993-3
(4822 727 20046) does not correspond with the exploded view.
This is corrected in Product Survey 1993-4 (4
Philips FL1.17 Only horizontal white and black lines.  TXT and sound OK. Check memory IC IC7240 100Hz eco-box (4822 209 52418).
 
Philips FL1.17 Only noisy green picture. Sound and TXT OK. Check IC7231 (SDA9205-2 noric; 4822 209 31056).
 
Philips FL1.17 Only red LED is on. Hardware protection. Check E/W protection T7540, T7541 (BC547C; 5322 130 42755) and
T7542 (BC857C; 5322 130 42756).
 
Philips FL1.17 Only white and black lines. OSD and TXT OK. Error 05. Check IC7231 (SDA9205-2; 4822 209 31056) on ECO-box.
 
Philips FL1.17 Overview of SOPS repair kits Overview of SOPS repair kits
----------------------------
FL1.0 AG00 upto AG03   4822 310 20492
FL1.0 AG04 and higher  4822 310 31921
FL1.1 25" and 28"      4822 310 31919
FL1.1 33"              4822 310 31932
FL1.2                  4822 310 31932
FL1.6  
Philips FL1.17 Picture disappears (fly back lines), ON STEREO and DUAL LEDs blink Check IC7430 (TDA4680). When TDA4680 is too hot there is no picture
(4822 209 31592).
 
Philips FL1.17 Picture disappears shortly after 30" or control does not function. When hot, 13,5 MHz clock stops working; change the value of R3123
to 1k2. 
 
Philips FL1.17 Picture often dark Check IC7201 in High End-box (SAA9042P/A; 4822 209 31851)
 
Philips FL1.17 Picture twists from top Voltage of pin 8-IC7450 (TDA3654Q) on the LSP has raised to ca. 20 V.
Check diode 6451 (BZX79/C3V6; 5322 130 34834 or
BZX79/C10; 4822 130 61219)
 
Philips FL1.17 Picture twists from top Voltage of pin 8-IC7450 (TDA3654Q) on the LSP has raised to ca.
20 V.  Check diode 6451 (BZX79/C5V6; 4822 130 80954).
 
Philips FL1.17 PIP picture not in order. Check R3345 (4822 111 41424) in PIP unit, check IC7755
(4822 209 63423). 
 
Philips FL1.17 Protection activated due to no +5V from LOT. Check IC7551, LM 358N (4822 209 71825). If IC7551 has to be
replaced, it is recommended:
1) for production code AG00-09 add diode BZX79-C18 (4822 130 31024)
   between 9240 and pin 8 of position 7551, with cathode to pin 8
   of IC7551.
2) for production 
Philips FL1.17 Red spikes in picture. Check A/D converter IC7231 ON ECO box (SDA9205-2; 4822 209 31056).
 
Philips FL1.17 Repair information Repair information
------------------
In case of one of the line transistors T7504 or T7506 is defective,
it is necessary to replace both transistors.
Order number 4822 130 62934 (2x ON4673).
 
Philips FL1.17 Repeated light-up of the standby-led after switching-off from standby. Change the following positions on the LSP:
Position 3250 from 47 ohm into 62 ohm (4822 116 52198)
Position 6251 from LLZ-C5V6 into LLZ-C7V5 (4822 130 80906)

REMARKS          :Introduced in production in week 9418.
Philips FL1.17 Set can only be operated with Remote Control Check whether "Child Lock" is disabled. To check this, see
"Frequently Asked Questions", "How to disable Child Lock".
 
Philips FL1.17 Set inoperative only red or green LED. Supply was 141V but no EHT. Line drive puls for T7506 (2SC4288A) too low.
L5503 defective (Line drive coil; 4822 157 63252)
 
Philips FL1.17 Set switched to EXT2 and back to programm. Check D6145 (LL4148; 4822 130 80446).
 
Philips FL1.17 Severe Moire patterning Most modern Colour Televisions use Automatic Gray Scale Tracking and
while the setting of the G1 may not seem to have a major effect on the
picture brightness on a modern set, incorrect adjustment can have the
effect of causing severe Moire patterning if 
Philips FL1.17 Shuts off and on again on Pr.nr. 1 after 3 hours. D6272 (BZX55B5V6) interruption when it becomes hot.
 
Philips FL1.17 Shuts off and on again on Pr.nr. 1 after 3 hours. D6272 (BZX55B5V6) interruption when it becomes hot.
 
Philips FL1.17 Sometimes in protection, or hor. width varies Check or resolder on LSP the pins of E/W bridge coil 5521.
 
Philips FL1.17 Sometimes vibration in vertical direction. Replace C2410 (150nF 5%; 4822 121 41854) on LSP.
 
Philips FL1.17 Spook in picture Use special antenna cables.
Codenumbers:
4822 321 61224  PAL 1 meter
4822 321 61225  PAL 2 meter
4822 321 61226  SECAM 1 meter
4822 321 61227  SECAM 2 meter        
 
Philips FL1.17 Spook lines visible (vertical interference lines at weak signal). Replace  C2536 by 1,5 nF (4822 126 11501) and
add item C2545     (1nF; 4822 122 31175) on the LSP.

REMARKS          :
Introduced in production in week 9334.
 
Philips FL1.17 Supply +5V too low, black horizontal bar in picture. Bad sync. Check/replace IC7551 (LM358N; 4822 209 70672)
 
Philips FL1.17 Supply switch-off sometimes Check the +5 stand-by. This voltage has to be 5.5V and may not vary.
When the voltage drops below 5.2V the set switches-off.
Cure: check D6266 for leackage (BZX79/F6V8; 4822 130 34278) or check
T7268 for leackage (BD943F; 4822 130 62742).
The 5.5V is meas
Philips FL1.17 Synchronization, picture disappears D6703 and T7704 defective on picture tube panel. 
 
Philips FL1.17 Ticking noise and line in picture Transistor 7381 (BC848C; 5322 130 42136) defective when hot.
 
Philips FL1.17 Total inoperative, leds blinking, error 99 Check and replace if necessary C2504 and/or 2505 (2kV HRR) on the
Large signal panel.
Replace by a 3kV15 HR-R capacitor if possible:
820pF    4822 126 13152
1nF      4822 126 13153
1,2nF    4822 126 13154
1,5nF    4822 126 13155
1,8nF    4822 126 13156
2,
Philips